Microstructure–mechanical property relationship in an Al–Mg alloy processed by constrained groove pressing-cross route

The constrained groove pressing-cross route process was implemented on a commercially annealed AA5052 alloy at room temperature, with up to two passes (strain of ～4.64) along the rolling direction and transverse direction. The results showed the formation of an ultrafine-grained structure with an average sub-grain/cell size in the 300–500?nm range. The indentation hardness and tensile strength increased significantly, up to ～75 and 105%, respectively, and became more homogenous with a uniform and isotropic trend, as compared to the annealed alloy. According to the Hall–Petch and Taylor models used, grain refinement and increasing dislocation density were proposed as the main strengthening mechanisms. Fractographic studies revealed a ductile-fracture behaviour, with a dimpled structure proportional to the UFG structure.     

焊丝中Si元素含量对铝合金接头裂纹敏感性的影响规律及机理

使用扫描电镜、能谱、温度场实时采集等测试方法，研究了焊丝中Si含量对AA6063铝合金GMAW焊接头热裂纹敏感性的影响规律及机理. 结果表明，当焊丝为纯铝时，鱼骨试样的焊缝中心会出现细长的焊接裂纹；当焊丝中的Si含量为4.5% ~ 6%时，裂纹的长度变短，但是开裂距离明显增加；当焊丝中的Si含量达到11% ~ 13%时，试样焊缝无裂纹出现. 随着Si含量的不断提高，合金易出现裂纹的凝固温度区间先增大后减小；焊丝中Si含量的不同还会影响凝固后期金属液的流动性，使得焊缝晶界处的物相成分和形态都有明显的区别；同时，Si含量的提高会使得接头的冷却速度先增加后减小，从而导致应力状态改变，热裂纹敏感性先升高后降低.     

时效工艺对纳米结构2297铝锂合金力学性能与微观组织的影响

采用535 ℃×2 h固溶制度,将热锻态2297铝锂合金固溶水淬后冷轧,冷轧压下量为95%,然后将轧制样品在不同温度(120~190 ℃)和时间(0~80 h)范围内进行时效处理。采用拉伸、扫描电镜(SEM)和透射电镜(TEM)等测试方法,分析时效温度和时间对铝锂合金组织与性能的影响。结果表明:时效前的大塑性变形能获得纳米结构组织,能促进T₁相均匀细小地析出,缩短合金达到峰时效的时间,最终成功制备了高强高塑性铝锂合金。在120~140 ℃温区内时效时,时效温度越高,达到峰时效的时间越短、强度越高。140 ℃达到峰时效时间缩短为40 h,此时合金的抗拉强度、屈服强度和伸长率分别为525 MPa、478 MPa和7.7%,主要强化相为细小的T₁相。在170~190 ℃温区内时效时,时效温度越高,达到峰时效的时间越短,但抗拉强度与屈服强度迅速下降。170 ℃时效8 h达到峰时效状态,此时合金的抗拉强度、屈服强度和伸长率分别是503 MPa、462 MPa和5.0%,主要强化相仍为T₁相,但已经明显粗化。     

Fe基非晶合金增强1060铝基多层复合材料的组织与性能

采用累积叠轧焊+中间退火法复合轧制1060Al/Fe基非晶多层铝合金复合板材。利用光学显微镜、扫描电镜、X-衍射分析仪以及拉伸试验机分析Al基复合材料的微观组织结构变化、断口形貌、物相组成以及力学性能。结果表明:Fe基非晶复合材料的增强体在300 ℃中间退火过程中发生部分晶化,在累积变形轧制过程中发生破碎,并随着变形道次的增加,破碎程度随之增大;复合板前6道次的累积轧制变形出现了明显的加工软化现象,并且随着变形道次的增加,其加工软化的效果愈明显;随着累积轧制变形道次增加,Al基复合材料的力学性能发生了明显的变化,第2道次轧制变形后屈服强度与抗拉强度达到了最大值为140 MPa和156 MPa,伸长率为5.53%,达到最佳综合性能。     

B对FeCoCrNiSiBx高熵合金激光熔覆层组织和硬度的影响

采用激光熔覆制备了FeCoCrNiSiB_x高熵合金熔覆层,利用光学显微镜、扫描电镜、X射线衍射仪和显微硬度计研究微量硼元素(摩尔比x=0、0.02、0.04、0.06、0.08)对FeCoCrNiSiB_x高熵合金熔覆层组织和硬度的影响。结果表明:无B高熵合金涂层组织主要为胞状晶。B的添加会促进枝晶的生成,逐渐形成鱼骨状树枝晶,但过量的B会破坏枝晶完整性,形成蠕虫状晶。此外,高熵合金熔覆层组织为FCC和BCC双相结构,B元素的添加会形成大量0.1~2.6 μm的Cr₂B第二相,有助于提高熔覆层硬度,其中x=0.06时激光熔覆层的硬度最高,约为537 HV0.2。     

再加工工艺对N18锆合金板残余应力的影响

采用“热轧+冷轧+退火”工艺对N18锆合金板进行再加工,通过X射线法分析板的表面残余应力,采用EBSD技术分析晶界取向差角分布和大小角度晶界。结果表明,热轧后N18锆合金板的表面残余应力呈现无规律分布状态;冷轧后板的表面残余应力均为压应力,其大小随着冷轧变形量的增加而增加;退火后板的表面残余应力值处于较低水平,当退火制度为500 ℃×2 h时,残余应力处于最低水平;退火后,板的微观结构以小角度晶界为主,且随着退火温度的升高,小角度晶界的密度先增加后趋于稳定。     

Sensitivity analysis of Johnson-Cook material parameters on adiabatic shear in different directions

ABSTRACT

This study investigates the effects of strain, strain rates, and forming directions (RD-rolling direction, TD-transverse direction, and ND-normal direction) on adiabatic shear, via dynamic impact compression tests using the Split Hopkinson Pressure Bar (SHPB) apparatus. A modified Johnson-Cook (J-C) constitutive model is proposed, which used to analyse the influence of the constitutive parameters on the sensitivity of adiabatic shear, employing a finite element software. The different sensitivities of adiabatic shear under different directions are explained by combining microscopic analysis and results from mechanical responses. The results show that the sensitivity of adiabatic shear can be related to the time of stress collapse in the following trend: ND?>?TD?>?RD; the sensitivities of these constitutive parameters on adiabatic shear are calculated and compared.     

Casting methods for the production of rotationally symmetric copper bimetals

ABSTRACT

Multiple-material products are characterised by a complex property profile which is achieved by combining the particular advantages of at least two different materials. Bimetal casting is an energy- and material-efficient technology for the production of multi-metallic objects. This paper describes the development of a semi-continuous casting process for the formation of a rotationally symmetric bimetal with a cohesive bonding character at the interface of a copper–tin alloy (CuSn6) and pure copper (Cu99.5). Initial experiments are conducted by static casting to evaluate the thermal process window. Based on the results of the initial experiments, a vertical semi-continuous compound casting process is developed. A stable cohesive bond between the joining partners is accomplished by forming a solid solution at the interface.

This paper is part of a Thematic Issue on Copper and its Alloys.     

热处理对挤压态Mg-6Gd-5Y-1Zn合金组织与性能的影响

通过对Mg-6Gd-5Y-1Zn(质量分数,%)合金在固溶和时效处理状态下显微组织和力学性能的研究发现,α-Mg基体、沿挤压方向分布的条状18R-LPSO相、少量的Mg₂₄(GdYZn)₅ 相以及细层片状的14H-LPSO相构成了挤压态合金的组成相。挤压态合金经固溶(T4)处理后,一部分18R-LPSO相溶入基体,并且基体中的14H-LPSO相伸长同时粗化。挤压态合金经过固溶加时效(T6)处理后,大量β′相从α-Mg基体中析出。T6态合金的室温力学性能最好,其屈服强度、抗拉强度及伸长率分别为272 MPa、406 MPa和6.1%。β′相沉淀也发生在挤压态合金的直接人工时效(T5)处理过程,但相比于T6处理,14H-LPSO相和β′相在基体中的体积分数均偏低。     

超高强7055铝合金铸锭均匀化工艺优化

采用光学显微镜、扫描电镜、差热分析及透射电镜等手段,对一种航空用超高强7055铝合金大尺寸铸锭的均匀化工艺进行分析与优化。提出分级提高均匀化温度的方法,在确保不发生过烧的情况下,最大限度改善铸锭质量。结果显示:低温预均匀化时,铸锭中析出大量的Al₃Zr相,能够大幅度降低对后续挤压变形的再结晶比例;对铸锭采用400 ℃×4 h+465 ℃×16 h+474 ℃×8 h的分级均匀化处理工艺,能够显著消除铸锭中低熔点相的含量,提高铸锭质量,同时相比于原工艺节省约13 h。新的均匀化处理工艺,不仅提高了生产效率,还能够为后续工艺提供良好的铸锭。